Cleaning Equipment

Soak Debond Tank

Part#: 81300

The soak debond tank allows for debonding the part from the grippers without twisting. This method is preferred in applications where twist debonding could cause delamination or other damage to the workpiece.

Features*

• Stainless steel construction
• Electric heat
• Programmable temperature control/sensor
• Simple push button cycle operation
• Easy access for clearing and maintenance
• High performance insulation to avoid heat loss
• Thermal insulation
• Easy fill and drain tank
• Low energy consumption
• Emergency stop button
• Dipping time timer
• Manual or automatic operation
• No water alarm light
• Interlock casters

Product Specifications

• Maximum product height: 10 inches (255 mm)
• Immersion platform size: 23 x 14 inches (584 x 355 mm)
• Immersion depth: 12 inches (305 mm)
• Cycle time: up to 15/min.
• Volume of water: 100 liters
• Electrical: 220V / 60 Hz / 3 Ø, 10 amps
• Machine size: 27 L x 33.5 W x 57.25 H inches (673 x 1016 x 1454 mm) with cover up (63 H inches (1600 mm)
• Weight: 394 lb (179 kg)

Options

• 208 V / 60 Hz / 3 Ø, 50 amps

*All external walls of the unit are insulated to help protect from hot surface contact. All specifications subject to change.

CNC Spindle Mounted Cleaning Tool

Part#: 82400, 82500

The spindle mounted gripper cleaning tool loads in a CNC machine to remove cured adhesive from grippers.

Part #: 82400 – Gripper Cleaning Tool Assembly

Part #: 82500 – Replacement Head

Features

• Mounts in any 3/4 diameter collet or end mill holder.
• Replaceable head for P/N 82400 tool assembly.
• Cleans an estimated 1,000 grippers before replacing head.
• Do not use with corrosion resistant grippers.

Handheld Pressurized Steamer

Part#: 84750

The handheld steamer provides pressurized steam for easy removal of residual cured adhesive from grippers and workpieces. Economical solution for prototypes or low-volume parts.

Features*

• 8 x 5.2 x 10.7 inches
• 3 lbs
• 6 oz water capacity
• Emits steam continuously for 10 minutes
• 15 ft power cord
• 900W
• 200˚F steam temperature

*Actual unit may vary from one shown.

Heavy Duty Steamers

Part#: 84870, 84880, 84890

These heavy duty steamers produce 60 PSI to unlimited hours of continuous steam pressure, and reaches temperatures up to 221°F at the tip. These steamers are ideally suited for cleaning away cured adhesive on grippers.

Part #: 84870 – Approximately 6 hours of continuous steam

Features

• 110V/120V 1200W element
• 1.25 gallon, 4.5 L water capacity
• Low water light indicator
• 61 PSI, 4.1 bar operating pressure
• Pressure/safety switch
• 30A heavy-duty contactor
• 12-gauge heavy-duty wiring
• Stainless steel tank and outer casing
• Carrying handle
• 15-20 minute heat up time

Part #: 84880 – Minimum 8 hours of continuous steam

Features

• 110V/120V
• 2.37 gallon, 9 L water capacity
• 1200W heating element
• Visual water level indicator
• Low water light indicator
• Regular tap water
• Ranco pressure control/li>
• 12-gauge heavy-duty wiring
• Stainless steel tank and outer casing
• 2 incoloy heating elements (1-spare)
• Carrying handle
• 30-40 minute heat up time

Part #: 84890 – Full-time steam

Features

• 110V/120V
• Automatic shut-off of pump in case water supply is interrupted
• Boiler thermostat reset switch
• Heavy-duty adjustable feet
• Low water light indicator
• Regular tap water
• Ranco pressure control
• 12-gauge heavy-duty wiring
• 1 Incoloy heating elements
• Stainless steel tank and outer casing
• Blow down valve
• 20-30 minute heat up time
• 20-amp plug required
• Direct connection to a water line

Scraper

Part#: 80030

The scraper is used to clean parts and grippers of cured adhesive after heating.

Features

• 5″ aluminum handle knife.
• Heavyweight adhesive removing blade.